ALF313 Low-profile Donut Ring Force Sensor
The ALF313 is ideally suited to engineering force measurements
Caractéristiques principales
- Full load range: 10kN, 20kN, 40kN, 80kN, 100kN, 120kN, 160kN, 200kN
- Load direction: compression
- Non-lin./hysteresis: 0.5/0.5% RL
- Low profile with center hole
- Ranges to suit bolt sizes from M6 to M36
- Stainless steel construction
About the ALF313 Low-profile Donut Ring Force Sensor
The ALF313 is ideally suited to engineering force measurements. It is designed for easy installation, usually between two flat faces bearing on its loading rings, either unattached or with retaining spigots positioned in the center hole. Alternatively tensile load transfer can be achieved via a tie rod assembly through the center hole. In this way the loadcell can indirectly measure tensile loads in a “fail-safe” mode.
We are happy to design variants of this loadcell to meet your specific requirements. Versions can be manufactured for fully compensated operation up to +250°C. Please consult our engineering department.
When this loadcell is rationalised the resistors are housed in a capsule located in the loadcell cable 100mm from the free end. Capsule dimensions are Ø10mm by 57mm.
Geometry: Axial strain cylinder in weather sealed case, with raised end load bearing faces and hole right through. For use in compression or in fail-safe tensile applications on a wide range of OEM or end-user applications.
Connections
For ranges up to 4 tonnes the loadcell is fitted with 2 metres of PVC insulated 4 core screened cable type 7-1-4C. Ranges above 4 tonnes are fitted with 7-2-4C cable.
- Excitation + = Red Signal + = Yellow Screen = Orange
- Excitation - = Blue Signal - = Green
The screen is not connected to the loadcell body.
Specifications
Parameter | 10kN | 20 to 200kN | Unit |
---|---|---|---|
Non-linearity - Terminal | ±0.5 | ±0.5 | % RL |
Hysteresis | ±0.5 | ±0.5 | % RL |
Creep - 20 minutes | ±0.1 | ±0.1 | % AL |
Repeatability (excluding rotational effects) | ±0.1 | ±0.1 | % RL |
Rated output - Nominal | 1.3 | 1.3 | mV/V |
Rated output - Rationalised | 1.0 | 1.0 | mV/V |
Rationalisation tolerance | ±0.5 | ±0.5 | % RL |
Zero load output | ±4 | ±4 | % RL |
Temperature effect on rated output per °C | ±0.005 | ±0.005 | % AL |
Temperature effect on zero load output per °C | ±0.03 | ±0.03 | % RL |
Temperature range - Compensated | -10 to +50 | -10 to +50 | °C |
Temperature range - Safe | -10 to +80 | -10 to +80 | °C |
Excitation voltage - Recommended | 10 | 10 | V |
Excitation voltage - Maximum | 10 | 20 | V |
Bridge resistance | 350 | 700 | Ω |
Insulation resistance - Minimum at 50Vdc | 500 | 500 | MΩ |
Overload - Safe | 50 | 50 | % RL |
Overload - Ultimate | 400 | 400 | % RL |
Sealing | IP65 | IP65 | |
Weight - Nominal (excluding cable) | 15 | 20-260 | g |
Avez-vous besoin de ce capteur pour votre prochain projet?
Demandez un devis dès aujourd'hui ou laissez vos coordonnées pour recevoir plus d'informations de la part de l'un de nos experts.
Téléchargements de produits
Faites-le à votre façon
Vous ne trouvez pas exactement ce que vous cherchez ? Nous proposons des capteurs et des systèmes de mesure standard, mais nous pouvons également vous aider à concevoir un capteur sur mesure ou une solution de mesure complète. N'hésitez pas à nous contacter pour obtenir des conseils ou un devis.
Parler à un expertProduits apparentés
Besoin d'autre chose?
ALF207 Load Washer
- Measuring range: ~10 kN to ~200kN
- For spaces with restricted height
- Various designs possible on request
ALF202 Donut Ring Force Sensor
- Measuring range: ~10 kN to ~200kN
- Very high structural load limit
- Different specifications possible
ALF203 Donut Ring Force Sensor
- Measuring range: up to 400 or 800 kN
- Tensile applications are ‘fail-safe’
- Different specifications possible